P18 MK2 Profile HP 1.100W 

P18 MK2 Profile HP (High Power) 1100W

Generally
LED-based moving head with a white LED light source of 1100 watts. Due to the optical properties of the headlamp should be used both as a spot/profile as well as Washlight.

Light source
The headlight should be equipped with a white 1100W light source. The headlight should produce at least 40,000 lumens of output. The color temperature should be about 6800 Kelvin. The CRI should be greater than 70. The light source should be flicker-free with a max. Repetition frequency of 3 kHz.

Optical system
Requirements for the optical properties of the headlamp are a clearly defined light beam with minimal stray light, a minimum beam angle of 6.5 ° and a maximum beam angle of 54 ° (1:8.3).

Control
The control takes place via DMX512. The control should be able to be used both via cable, as well as via a standard built-DMX radio. Also, a W-Lan / Bluetooth module to control the headlight should be integrated. The activation of the LED module should be possible in at least two different drive curves (linear and exponential). Pan / Tilt, color mixing and rotations / positioning should be controlled in 16bit. The dimmer must work absolutely continuously from 0-100%. To adapt to different camera systems, different repetition frequencies (up to 3 kHz) for the LED module can be selected via DMX / RDM.

Control
The headlamp should be controlled by the DMX512, RDM, Artnet, sACN control protocols, 5-pin XLR lockable connectors, and 2 lockable Ethernet (IN and OUT) ports to connect the data lines. All user-settable device settings should be selected and stored via a control panel located on the headlamp with a graphic color touch LCD display or via the data line in conjunction with a control unit. The graphic display should be rotatable. The headlamp shall have a battery buffering for the adjustment of the headlamp characteristics, e.g. for setting the DMX address. The headlamp should have the possibility of at least 20 program steps that can be stored on the device. Several headlights should be able to be switched together in the form of a series circuit, with a device to act as a master whose program settings should be taken over by the connected headlights.
The headlamp should have a factory built-in receiver module for control via radio DMX. The protocol of the radio module must be compatible with Lumen radio stations. Five different cooling modes should be able to be set on the headlight, with the quietest modes a volume of 28 dB (A) should be achieved.

Effect unit
The effect unit should have 1 color wheel with 6 full or half colors plus a HCRI filter, 2 gobo wheels, one with at least 8 static interchangeable gobos and one with 6 rotating, changeable and positionable Gobos, an animation wheel and sparkle effect feature. In addition, the effects unit should also have an 18 slats iris, a shutter slide module (+-65 ° rotatable and each blade +-28°) with 4 blades, each blade completely closing, 2 prisms rotatable and positionable, 2 stepless, exchangeable frost filter and focus feature. The zoom range should cover at least 6.5 ° - 54 ° (1:8.3). The color mixing should be done via CMY with a variable CTO.
 
Installation
The headlamp should have a basement and operate in any position. Where in the mounting of the headlight with two omega brackets, which can be screwed with terminals, should be feasible. The omega brackets should be able to be mounted on the headlamp with Camloc quick-release fasteners. A reinforced anchor point on the base of the headlamp for a safety rope must be present.

Mains connection and power supply
The headlight should be able to be operated with mains voltages of 100V - 240V and 50 - 60 Hz. The power consumption should be at a maximum of 1500VA. The headlight should have powerCON TRUE1 IN / OUT connectors.

Cleaning and maintenance
The headlight should be as easy to service as possible. These include easy-to-clean lenses, effects and air filters, as well as slide-in technology for CMY / CTO, color / gobo wheels, iris and shutter. The bays must be constructed in such a way that they can be pulled out without tools and additional disconnection of cable connections! The optical system should be dustproof. If necessary, the LED module should be exchangeable by the experienced user himself and without soldering.

Surroundings
The headlamp should be operated in a dry, well ventilated environment with a temperature not exceeding 40 ° C.

Dimensions and weights
Maximum dimensions: W 475 x H 755 x D 307 mm. Weight: 32kg