CODA AUDIO GmbH

https://www.codaaudio.com
Boulevard der EU 6
30539 Hannover
Deutschland

Sales Requests
contact@codaaudio.com
  +49 511 866 55 888
  +49 511 866 55 887
en de

LINUS14

CODA Audio GmbH

1
2
3
LINUS14 is a fully integrated DPS-controlled Class D-IC amplifier for all CODA AUDIO loudspeaker systems. It has 4 analog and 8 digital LiNET (AES) input channels, which can be flexibly routed to the 4 outputs of 3,500 W @ 4 Ohm each. LINUS system amplifiers are remotely controlled and monitored via the network-based LINUS-LIVE Remote Control Software (PC & Mac).

Technical specifications, datasheets, descriptions and tender texts for LINUS14

Info
tender specification text
The controller output stage should deliver an output power of 4 x 3,500 watts RMS at 4 ohms. It should be optimally adapted to connected full-range loudspeaker systems, bass expansions and low bass expansions by providing loudspeaker presets. The DSP processing in the loudspeaker presets will take place in IIR and FIR filter technologies. Pre-calibrated contour filters, as well as real-time protection functions against thermal overload and excessive membrane deflection of the loudspeaker, as well as runtime and phase corrections. The DSP architecture will include four analog, eight digital AES/EBU inputs and four outputs. The balanced analog inputs should have an input impedance of 12 kOhm. The four outputs should have a signal-to-noise ratio of <111 dB (A-weighted) when using the analog inputs, and <119 dB (A-weighted) when using the digital inputs. The attenuation factor should be >10,000 (at 1 kHz and 8 Ohm). The DSP with 32-bit floating point processing should operate at 96 kHz sampling rate and use cascaded A/D converters. The latency of the system should not exceed 0.6 ms with minimum process sing. For each channel of the power electronics, an integrated comparator for the use of sensor-controlled bass and low bass extensions should be available. The special sensor subwoofers should be connected via two 5-pin XLR connection fields located on the rear panel. The TCP/IP network protocol for remote control of the controller output stage should operate at a speed of 100 Mbit/s and enable remote monitoring of up to 100 devices in star-shaped, linked or hybrid arrangement. The electrical connection of the network is to be made via two RJ-45 inputs and outputs at the rear using CAT5e U/FTP (or higher) cables. Free remote control and monitoring software for Mac and PC is available to provide access to signal routing, polarity, muting and gain parameters, delay time, and user-specific filter parameters. In addition, input and output levels and states, component loads, and network characteristics and disturbances should be displayed. An integrated XLR connector panel with all balanced analog signal inputs and all digital AES/EBU inputs (via RJ45 connectors) should be located on the rear panel. Two NL4 outputs and one NL8 output should be available for the loudspeaker outputs. For the power supply there should be a 32A PowerCon on the rear panel. Its physical dimensions should be 483 mm in width, 88.9 mm in height and 453 mm in depth. It is to be able to be mounted in 19" racks with rack tubes provided for this purpose and use 2 height units. The weight of the controller output stage should be 14.75 kg. The manufacturer's warranty should be 5 years. 
GAEB
TEXT
short summary
LINUS14 is a fully integrated DPS-controlled Class D-IC amplifier for all CODA AUDIO loudspeaker systems. It has 4 analog and 8 digital LiNET (AES) input channels, which can be flexibly routed to the 4 outputs of 3,500 W @ 4 Ohm each. LINUS system amplifiers are remotely controlled and monitored via the network-based LINUS-LIVE Remote Control Software (PC & Mac). 
product type
amplified 4-channel system controller 
order code
Coda-LINUS14D 
product link
Product Name
LINUS14 
Audio
No. of channels
4 pcs
Frequency response, from
20 Hz
Frequency response, to
20000 Hz
Input impedance, balanced
12.00 kOhm
Signal to Noise Ratio (A-weighted)
119.00 dB
Intermodulation Distortion(for measurement method see text field)
<0,005%, 4 Ohms P/2 (20 Hz - 20 kHz) 
Connectors
output connector > Speakon NL4xx
2 pcs
output connector > Speakon NL8xx
1 pcs
RJ 45
yes 
Input analog
4x XLR-F 
Input Digital
8x LiNET / 8x AES3 (RJ45) 
Digital Link
1x RJ45 LiNET-OUT 
output connector - others/individually
XLR-F 5pol. 2-Ch. Comparator 
Control
DSP control
yes 
LED - Status Display
yes 
Electrical
power consumption amps, max
52.00 A
power consumption watt, max
4450.00 W
AC Volts, min
85 V
AC Volts, max
264 V
AC Frequency, min
47 Hz
AC Frequency, max
63 Hz
IP rating
operating temp, min
5.00 °C
operating temp, max
55.00 °C
Power per channels at 2 Ω
2600 W
Power per channels at 4 Ω
3500 W
Power per channels at 8 Ω
1800 W
power input connector
Powercon 
cooling
active 
networkable
yes 
Software name
LINUS-LIVE 
Ventilation
yes 
Mechanical
weight
15.75 kg
width
483.00 mm
height
88.90 mm
length
453.00 mm
height in rack-units
2 U

add to list

Collect interesting products in a list and download tender specifications at once

show list

Downloads
no files provided by the manufacturer